Español Français EnglishOwner’s ManualRead this manual for complete instructions1009 • Form No. 0504949CPatent pendingContents 2 Important Safety I
English 10 4. Practice SprayingYou will need: • Scrap material / cardboardHold the Spray Gun LevelPractice on a piece of scrap material/cardboardT
11EnglishSpray Pattern Overlap Your StrokesSpray Technique8” - 10”(20 - 25 cm)!GOOD SPRAY PATTERN BAD SPRAY PATTERN: TAILINGCORRECTSee page 12-14Sta
English 12 SafetySpraying Troubleshooting -Clear the Spray TipYou will need: • Scrap material / cardboardDo not attempt to unclog or clean the tip
13EnglishSafetySpraying Troubleshooting -Clean the Spray Gun FilterYou will need: • Wrench • Warm, soapy water for latex material • Mineral sp
English 14 SafetySpraying Troubleshooting -Clean the Inlet FilterYou will need: • Warm, soapy water for latex material • Mineral spirits for oil
15EnglishSafetyShort Term StorageThis procedure should be used when taking a short term break or when ending your project for the day. If your break
English 16 SafetyCleanupYou will need: • A water source that can be delivered with a garden hose (latex materials only) • Mineral spirits if usi
17English 5. Remove the inlet lter from the suction tube and place it into waste container. 6. Thread pump cleaning adapter onto garden hose.
English 18 Cleanup - Oil-Based MaterialsFollow these steps if you sprayed oil-based and do not have a g
19EnglishCleaning the Spray Gun ComponentsYou will need: • Soft bristled brush • Light household oil • Warm, soapy water if using latex materi
English 2 Important Safety InformationRead all safety information before operating the equipment. Save these instructions
English 20 Long Term StorageYou will need: • Light household oil • Rags 1. Remove the suction set. 4. Turn power OFF. 2. Pour approximatel
21EnglishReplacement of the outlet valve may be necessary if spray performance remains Problems secti
English 22 Troubleshootingpressure by following Pressure Relief Procedure (page 7).Problem A: The sprayer do
23EnglishProblem E: The spray gun leaksCause Solution1. Gun lter housing is loose Tighten handle2. Internal parts of spray gun are worn or dirty Ta
English Français Español 72612345Sprayer • Pulvérisateur • Rociador Parts List • Liste de Pièces • Lista de piezas
EnglishEspañolFrançaisEspañol 73Item Article ArticuloPart No. No de piéce Pieza No. English - Description Français - Description Español - Descripci
English Français Español 74Parts List • Liste de Pièces • Lista de piezas1456327Spray Gun • Pistolet • PistolaItem Article ArticuloPart No. No de pié
EnglishEspañolFrançaisEspañol 75Tip/Filter Accessories • Accessoires de buse/ltre • Accesorios de punta/ltroEnglish - All spray tips and filters lis
English Français Español 76Limited WarrantyAIRLESS PAINT SPRAY EQUIPMENT This product, manufactured by Wagner Spray Tech Corporation (Wagner), is war
3EnglishHAZARD: GENERAL Can cause severe injury or property damage.PREVENTION: • Read all instructions and safety precautions before operating eq
SprayguardSpray tipassemblySpray tipSaddle seat**Washer**Saddle seat and washer come pre-assembled inside spray guard**Material container holder(round
5English1. AssemblyYou will need: • Adjustable wrench IMPORTANT: Do not plug in the power cord until assembly is complete. IMPORTANT: Do not car
English 6 Proper use and functionsSpecificationsWeight ...20.5 lbsFlow rate ...0.24 gal/minut
7EnglishPressure Relief Procedure**Perform when instructedBe sure to follow the Pressure Relief Procedure when shutting the unit off for any purpose.
English 8 2. Load MaterialYou will need: • The material you plan to spray • Extension cord • Waste bucket 1. Push the red inlet release but
9English3. Getting Material to FlowYou will need: • Scrap material / cardboard • Drop cloths to protect oors and furnishings from overspray 3.
Commenti su questo manuale