WAGNER EP2105 Manuale del Proprietario

Diaphragm Pumps1150Piston PumpsEP2105EP2205EP2300EP2300seEP2400EP2510GP2605GP2905HVLPCS5100CS8100CS9100Maxum II GunDiaphragm Pumps1150Piston PumpsEP21

84. Set Prime/Spray Ball Valve to the Prime position.Figure 5. Set Prime/Spray Ball Valve to Prime5. Turn the ON-OFF switch to the ON position.6. Gra

9For a new unit, follow purging and priming steps above. Forunits already in service, also purge water or solvent fromthe system as described above,

101. Engage the gun safety latch.2. Shut off the motor and turn the pressure control knobcounterclockwise as far as possible.3. Turn the prime/spray b

11Spraying TechniqueYou can learn to spray paint as easily as you can learn topaint with a brush or roller. You can get a professionallooking job in

127. The spray gun should be triggered (turned off and on)on each stroke. This will save paint and avoid paintbuildup at the end of the stroke. Howe

13MAINTENANCERoutine operator maintenance on this unit is minimal. Onlythree daily procedures are required: (1) lubricating theupper packings, (2) cl

14Refer to Figure 14 (left). 1. Loosen and remove siphon tube assembly by turningcounterclockwise. 2. Remove front cover. 3. Remove packing nut cov

15Repacking Fluid SectionContinued from Page 14(Refer to Figure 14, Page 14)16. Remove lower O-Ring (27) from inlet valve holder.17. Place cylinder (8

16NEVER OPERATE PUMP WITHOUT FRONT COVER INPLACE.WARNINGBrushes should be inspected periodically to insure uninter-rupted service. Their life depends

17PROBLEM CAUSE REMEDYUnit will not run Blown panel fuse or tripped Check and replace/resetbreakerUnit not plugged in Plug inPressure control knob set

18TROUBLESHOOTING CONTINUEDPROBLEM CAUSE REMEDYPoor spray pattern Tip too large Change to smaller tipPressure adjustment wrong Adjust pressure contro

1911192012345667891010921213151416171821222324252026 Figure 16- EP2300 Final AssemblyITEM PART NO. DESCRIPTION QTY1 0294611 Hose, Fluid,1/4 NPT 12 050

20Figure 17- Low Boy Final AssemblyEP2300 LOW BOY FINAL ASSEMBLY - FIGURE 17ITEM PART NO. DESCRIPTION QTY.ITEM PART NO. DESCRIPTION QTY.1 - - - - - -

21Figure 18 - Cart AssemblyCART ASSEMBLY - FIGURE 18ITEM PART NO. DESCRIPTION QTY.ITEM PART NO. DESCRIPTION QTY.6 9890104 Cap, Axle 27 54458 Screw 28

22LOWBOY CART ASSEMBLY - FIGURE 19ITEM PART NO. DESCRIPTION QTY. ITEM PART NO. DESCRIPTION QTY.Figure 19- LowBoy Cart Assembly11 0294445 Handle, Cart

23 PRESSURE CONTROL ASSEMBLY - FIGURE 20Item Part No. Description Qty.Item Part No. Description Qty.Figure 20 - Pressure Control Assembly1285121113102

24Figure 21 - Fluid SectionNOTE:#20 Torque250 IN. LBS.NOTE:#28 Torque40 FT. LBS.REPAIR KITSKIT NO. DESCRIPTION0294905 Packing Kit (* Items Included)

25Figure 22 - Transducer AssemblyTRANSDUCER ASSEMBLY -FIGURE 22321456780294185 SUCTION SETASSEMBLY - FIGURE 23ITEM PART NO. DESCRIPTION QTY1 0090447 E

26EP2300 MOTOR ASSEMBLY - FIGURE 24ITEM PART NO. DESCRIPTION QTY.1 01678 Brush Holder 22 01694 Motor Brush 23 01686 Brush Cap 24 01783 Stud 25 19498 S

27EP2300 Drive Assembly - Figure 253124578967106111213141516171819202122232425262728293031323334353637383940ITEM PART NO. DESCRIPTION QTY.ITEM PART N

1EP2300 Piston Pump1297 © 1997 Wagner Spray Tech. All rights reserved. Form No. 0294724EModel Numbers:0294006 Cart Mount0294036 Low BoySprayTECH1770

281234567890294220 DUMP VALVE ASSEMBLY - FIGURE 26ITEM PART NO. DESCRIPTION QTY. ITEM PART NO. DESCRIPTION QTY.1 0294194 Filter Body Assembly 12 14069

29Item Part No. Description Qty.DUMP VALVE ASSEMBLY - FIGURE 27Figure 27 - Dump Valve AssemblyItem Part No. Description Qty.123451 0294502 Housing,

30ACCESSORIESGUN FILTERSPartNumber Description0153—— Tungsten Carbide Flat Tips0153003 Tip Guard, Flat Tip0291004 Hose, Whip End, 3' x 3/16"

32Two Year WarrantySpray Tech, a division of Wagner Spray Tech Corporation ("Spray Tech"), warrants this product against defects in material

2GROUNDING INSTRUCTIONSThis product must be grounded. In the event of an electricalshort circuit, grounding reduces the risk of electric shock byprov

3CONTENTSSafety Warnings... 4-6Specifications...

4• Maximum operating range of the gun - 3000 PSI fluidpressure.• NEVER aim the gun at any part of the body.• NEVER allow any part of the body to come

5WARNINGHAZARDExplosion or fire - Solvent and paint fumes can explode orignite causing property damage and or severe injury.• Exhaust and fresh air in

6• Halogenated hydrocarbon solvents such as methylenechloride and 1,1,1 - Trichlorethane are not compatiblewith aluminum and may cause an explosion. I

7SPECIFICATIONSMODEL EP23001. GPM----------------------------------------------------------2/32. Maximum pressure------------------------------- 3000